Paper roll cutter specifications and replacement hardware

Looking for the right cutter size, checking whether your paper roll will fit, or replacing a small part? Here are the measurements and hardware details in one place.

Cutter sizes and dimensions

The cutter size refers to the maximum paper-roll width. The complete dispenser is a little wider, so please allow for its overall length when planning your space.

Cutter size / maximum roll width Overall dispenser length
12 inches (30.5 cm) 14 inches (35.6 cm)
18 inches (45.7 cm) 20 inches (50.8 cm)
24 inches (61 cm) 27 inches (68.6 cm)
36 inches (91.4 cm) 40 inches (101.6 cm)

All four sizes share these specifications:

  • Overall height: 6.5 inches (16.5 cm).
  • Maximum roll diameter: 9.5 inches (24.1 cm).
  • Minimum paper-roll core opening: 1 inch (2.54 cm).
  • Wooden dowel diameter: 1 inch (2.54 cm).
  • Colors: silver and black.
  • Construction: steel frame with a wooden dowel.
  • Designed for kraft, freezer and butcher paper. The paper roll is not included.

Please check the roll width, outside diameter and core opening before buying paper. The number of feet on a roll depends on the thickness of the paper, so the physical measurements are the best way to check the fit.

Supported mounting position

Use the cutter on a stable, level tabletop or in its supported horizontal mounting position. The wooden dowel and tear bar must stay level and parallel to the floor. Vertical mounting is not supported, and under-counter mounting is not a tested setup.

Missing a part? We can help

Before buying replacement hardware, please email info@diycrew.co with your order ID, cutter size and the part you need. You can open a missing-parts claim within your one-year warranty. Depending on your case and parts availability, we can help with the missing parts or a replacement unit.

If we send a replacement unit, you are welcome to keep the original and save its usable parts as spares in case another piece is lost or damaged later.

Assembly screws and mounting hardware

If you prefer to source a part yourself, the following are replacement references and online examples. Please match the thread, diameter and length to the part you are replacing.

Part Replacement specification Online example
Main assembly machine screws M6 × 1.0 mm thread pitch × 16 mm length; Phillips pan head, stainless steel 18-8 (A-2) Bolt Depot #5189
Small assembly machine screws M3 × 0.5 mm thread pitch × 8 mm length; Phillips pan head, stainless steel 18-8 (A-2) Bolt Depot #6831
Wood-screw alternatives for suitable mounting surfaces #10 × 2 inches or #10 × 2½ inches; Phillips flat head, stainless steel 316 Bolt Depot #16374 or #16375

The included wall-mounting kit is described in our installation guide as M5 × 40 mm screws with plastic wall plugs. The #10 wood screws above are alternative sourcing options, rather than the same specification as the supplied kit. Please choose screws and anchors suitable for your wall. The supplied plastic plugs are not suitable for unsupported drywall or plasterboard.

Wooden dowel replacement references

The wooden dowel is 1 inch (2.54 cm) in diameter. If you choose to buy a replacement, please use a dowel with the same diameter. The links below offer different lengths; please check the length against your original dowel and cutter before ordering, or ask us to help confirm the fit.

Rubber feet

A 19 mm push-in rubber foot is a possible aftermarket option. This eight-piece pack is one sourcing example, but it is not an exact match to the original feet. Please contact us or check the fitting dimensions before purchasing.

These links are examples from independent suppliers; availability and product options may change. If you are unsure which part to choose, we are happy to help at info@diycrew.co.

Still need help

Can't find what you're looking for? Reach out and we'll sort it